Baso BGC278 Series BASOTROL Manual de usuario descargar pdf

Installation Instructions BGC278

Issue Date April 1, 2013

Part No. BASO-INS-BGC278, Rev. - www.baso.com

BGC278 Series BASOTROL®

CE Approved Gas Valve

Installation

IMPORTANT: These instructions are intended as a

guide for qualified personnel installing or servicing

BASO Gas Products. Carefully follow all instructions

in this bulletin and all instructions on the appliance.

Limit repairs, adjustments, and servicing to the

operations listed in this bulletin or on the appliance.

WARNING: Risk of Fire or Explosion.

The system must meet all applicable local, national,

and regional regulations. Improper installation may

cause gas leaks, explosions, property damage, and

injuries.

WARNING: Risk of Fire or Explosion.

To prevent leakage of upstream gas, shut off the gas

supply at the main manual shutoff valve before

installing or servicing the BGC278 valve. Failure to

shut off the gas supply can result in the release of

gas during installation or servicing, which can lead to

an explosion or fire, and may result in severe

personal injury or death.

Mounting

CAUTION: Risk of Equipment Damage. To

prevent damage to the valve when mounting to

pipework, do not use a wrench on any surface other

than the casting flats provided at the inlet and outlet

ends of the valve body.

To install the BGC278 valve:

1. Ensure that the specified maximum ambient

(surface) temperature is not exceeded (see the

Technical Data section).

2. Ensure that the power supply voltage is compatible

with the required control valve voltage.

3. When installing the valve on the manifold, ensure

that the gas flows through the valve body in the

direction indicated by the arrow on the valve body.

If the valve is installed with the gas flow in the

opposite direction of the arrow, leakage can occur.

4. Shut off the gas at the main manual shutoff valve.

5. Mount the valve to the pipework. The BGC278

valve may be mounted on a horizontal manifold

with the solenoid coils pointed up (vertical) or in any

position not exceeding 90° from the vertical. The

valve also may be mounted on a vertical manifold

in any position around its axis (see Figure 1). Do

not install the solenoid coil upside

down. Install

vertically wherever possible.

90° Maximum

from Vertical

90° Maximum

from Vertical

Limited Horizontal and Vertical

Vertical mounting may

be 360º around its axis

with the gas flow either

up or down, but always in

the direction of the arrow.

Figure 1: BGC278 Valve Mounting Positions

1 2 3 4 5 6

Indice de contenidos

Pagina 1 - CE Approved Gas Valve

Pagina 2 - Figure 2) and an

2 BGC278 Series BASOTROL CE Approved Gas Valve Installation Instructions 6. Use an approved pipe joint sealing compound on the male threads befor

Pagina 3

BGC278 Series BASOTROL CE Approved Gas Valve Installation Instructions 3 Wiring! WARNING: Risk of Shock. Disconnect the power supply before makin

Pagina 4 - Repairs and Replacement

4 BGC278 Series BASOTROL CE Approved Gas Valve Installation Instructions Repairs and Replacement Table 1: Replacement Solenoid Coil Part Number D

Pagina 5 - Technical Data

BGC278 Series BASOTROL CE Approved Gas Valve Installation Instructions 5 Technical Data Product BGC278 Series BASOTROL CE Approved Gas Valve Typ

Pagina 6 - Technical Data (continued)

6 BGC278 Series BASOTROL CE Approved Gas Valve Installation Instructions Technical Data (continued) Agency Listings CSA (AGA/CGA) Certificate Num

Comentarios a estos manuales

Sin comentarios

Baso BGC278 Series BASOTROL Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Baso BGC278 Series BASOTROL. BASO BGC278 Series BASOTROL User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Baso BGC278 Series BASOTROL